Accessories

Bow rail, pair (450 TC)

Safety enhancing bow rails out of polished stainless steel. The package includes two rails. Diameter of steel tube ø25 mm. Makes boarding easier and provides safety.

Bowrail (shark fin)

Bow rail made of acid-proof steel, painted in grey. Diameter ø25 mm. Makes boarding easier and provides safety.

Bowrail (shark fin), pair, polished

Bow rail made of acid-proof steel. Diameter ø25 mm. Makes boarding easier and provides safety.

Bowrail (shark fin), polished

Bow rail made of acid-proof steel. Diameter ø25 mm. Makes boarding easier and provides safety.

Canopy

Harbor and driving canopy protects from wind, rain and sun in port and offshore. Small holes at the bottom of rear part of the canopy allow the use of the rear rail on the boat. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The canopy arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Canopy (Saiman)

The Terhi Saiman canopy protects from wind, rain and sun. It can be used whilst rowing/driving the boat, but also to cover the boat with docked in the harbor. The canopy fabric should be stored warm and dry at the end of the boating season.

The canopy is not suitable for winter storage. The canopy arches are not designed to withstand the weight of snow. Do not use the arches to support a separate winter cover either.

Cleat 102mm

Cleat 102 mm, acid-proof steel, polished. Includes fastening screws.

Cleat 8” polished

Cleat 8″, acid-proof steel, polished. Includes fastening screws.

Cleat Terhi 6, polished

Cleat 6″, acid-proof steel, polished. Includes fastening screws.

Comfort Pack (480 BR)

Includes the following accessories factory-installed at the time of production: Front handrail pair (748332-TER; Windscreen side rails pair (748303-TER); cushion set (748500-TER) and Stearn canoby (547650-TER)

Comfort Pack (480 Cabin)

A preconfigured set of popular/recommended accessories, suited for Terhi 480 Cabin. The pack includes the following accessories:

Trim tabs (78809-TER)
Cushion set (748500-TER)

Note! Only available as factory-installation when the boat is ordered straight from the production lines.

Comfort Pack (480 Sport)

A preconfigured accessory package suited for Terhi 480 Sport. The Comfort Pack includes the following additional accessories:

Bow rails, pair (748332-TER
Windscreen side rails, pair (7483031-TER)
Cushion set (748500-TER)
Stern canopy (5476501-TER)

Note! Factory installation only, for boats ordered straight from the production lines.

Comfort Pack (480 TC)

A preconfigured accessory package for Terhi 480 TC. The Comfort Pack includes the following additional accessories:

Bow rails, pair (748332-TER)
Side railings for windscreen, pair (748304-TER)
Cushion set (747594-TER)
Stern canopy (547540-TER)

Note! Only for factory installation, for boats ordered straight from the production line.

Console complete, boat grey

With this conversion package you can convert your Terhi 445 or Terhi 450 boat into a wheel steerable boat! The package includes components for installing a complete driving console for Terhi 445 or Terhi 450 Terhi with its electrical equipment. The package also includes a windscreen and a polished windscreen rail. The color of the console is “boat grey”.

Console cover

Protective cover to be pulled over the steering console. Protects from dirt and rain and prevents for example rainwater from entering the instrument panel.

Console cover

Protective cover to be pulled over the steering console. Protects from dirt and rain and prevents for example rainwater from entering the instrument panel.

Cover

Harbor cover protects the boat from dirt and rain while the boat is in port. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The cover arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Cover for the bow of 480 BR/Sport

Cover your boat with a harbour cover for the stern and a bow cover for the front part of the boat. Covers protect the boat from dirt and rain while the boat is in port. The cover is not suitable for storing the boat outdoors in the winter. The cover should be stored in a warm, dry place when the boat season has ended.

Cup holder to rowlock socket

Fasten the cup holder into the rowlock socket

Cushion for backrest rail 7445023-TER 450 TC

This cushion requires a backrest rail (7445023-TER) on the boat. Fastening on the backrest rail with a zipper. After use it is recommended to move cushion to a shelter from the rain.

Cushion for backrest rail 71556-TER 400 C/CC

This cushion requires a backrest rail (71556-TER) on the boat. Fastening on the backrest rail with a zipper. After use it is recommended to move cushion to a shelter from the rain.

Cushion for middle bench with storage space

This cushion fits on top of the middle bench with storage space, which is sold as an accessory for the Terhi 390 and Terhi Saiman boat models (fitting with snap fasteners). After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of the cushion may vary between production batches.

Cushion set (400/400 CC)

A stylishly dual-tone grey cushion set for the Terhi 400 / 400 CC models. The set includes the cushion for the seat in the very bow, the middle bench and the stern bench.

We recommend stowing away the cushions in a dry space after use, to prolong the lifespan of the cushions.
Note! The placements of the snap buttons (for fastening the cushions to the benches) might vary between production batches.

Cushion set (Tender)

A comfortable, stylishly grey seat cushion for Terhi Tender’s lengthwise seat. Also suited for the older Terhi Baby Fun model. The cushion is fastened to the seat with snap fasteners, which are included in the package. We recommend removing the cushion after use and storing it in a dry place sheltered from rain and moisture. This keeps the cushion in better shape for a longer time.

Note! The fastening points of the cushion may vary between production batches.

Cushion set for the console front (400 CC)

A seat cushion and a padded backrest for the seat in front of the steering console on the Terhi 400 CC model. The package includes two cushions. Cushions for other seats (74005-TER), as well as the backrest rail of rear seat (71556-TER) and cushion for backrest rail (71557-TER) are sold separately. We recommend stowing away the cushions in a dry space after use, to prolong the lifespan of the cushions. Please note! The fastening points of the cushions may vary between production batches.

Cushions

Cushion set for Terhi Saiman -models includes grey cushions for the bow, middle- and rear seats. After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of the cushions may vary between production batches.

Cushions

The cushion set includes three cushions for the bow, side and rear seats. After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of the cushions may vary between production batches.

Cushions

The cushion set includes cushions for all three seats. After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of the cushions may vary between production batches.

Cushions

This cushion set fits on Terhi 480 TC -model. Stylish seat cushion set provides more comfort on the boat. The set includes seven cushions – one for front seat, one for both console seats and two seat cushions + two backrest cushions for the rear seat. After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of the cushions may vary between production batches.

Cushions

This cushion set fits on Terhi 480 BR, 480 Sport & 480 Cabin -models. A stylish seat cushion set provides more comfort on the boat. The set includes five cushions – one for front seat and two seat cushions + two backrest cushions for the rear seat. After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of the cushions may vary between production batches.

Cushions

A stylish, dual-tone grey cushion set for the Terhi 450 -models. The set includes the cushion for the bow-, port side- and stern benches. After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of the cushions may vary between production batches.

Cushions

Cushion set for Terhi 390 -model. The set includes cushion for each seat (3 pcs). After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of the cushions may vary between production batches.

Cushions

A stylishly dual-tone grey cushion set for the Terhi 480 CC – the set fits also on older Terhi models 475 BR, 475 Open CC and 475 Open FC. The cushion set includes cushions for the bow and rear seats and a backrest cushion of the rear seat. After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of the cushions may vary between production batches.

Cushions armrest set

A set for the Terhi 450 Sloep -boat model. Armrest cushions for the driver and co-driver. The set includes two dark grey cushions and mounting parts. Mounting on the gunwale with snap fasteners. After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of the cushions may vary between production batches.

Cushions seats 5 pcs

A set for the Terhi 450 Sloep -boat model. A stylish dark grey seat cushion set provides more comfort on the boat. This cushion set includes five seat cushions – one for the rear seat and four for seat in the bow area. After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of the cushions may vary between production batches.

Cushions sundeck

A set for the Terhi 450 Sloep -boat model. Two dark grey cushions on the sunbed plywood parts. Mounting with snap fasteners. The use of sunbed cushions requires also sunbed plywood parts and a seat cushion set on the boat. After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of the cushions may vary between production batches.

Cushions to backrest

A set for the Terhi 450 Sloep -boat model. The set includes three dark grey backrest cushions for the bow, one backrest cushion for the stern and mounting parts. The stern backrest cushion requires a high stern rail (7445021-TER) on the boat. Mounting of the backrest cushions for the bow with snap fasteners. Fastening of stern backrest cushions on the high stern rail with zip fastening. We recommend stowing away the cushions in a dry space after use, to prolong the lifespan of the cushions. Note! Backrest cushions cannot be mounted to the bow of a boat with bow rails. The fastening points of the cushions may vary between production batches.

Davit hook

With davit hooks you can hang a lightweight tender boat on davits of bigger boats/vessels. Material acid-proof steel. Mounting through the hull of the boat. The boat has reinforcement parts at mounting points.

Davit hook

With davit hooks you can hang a lightweight tender boat on davits of bigger boats/vessels. Material acid-proof steel. Mounting through the hull of the boat. The boat has reinforcement parts at mounting points.

Drop-in rowing unit for Saiman

Turn your Terhi Saiman into an excellent fitness rowing boat!

This retrofittable sliding seat is designed for Terhi Saiman rowing boat and it transforms your traditional Saiman rowing boat into a real fitness equipment for the summer cottage. This fitness rowing accessory has been developed for the Terhi Saiman in collaboration with Finnish adventure rower Jari Saario. The sliding seat adds extra power to every stroke by engaging your leg muscles.

The sliding seat replaces the standard center seat and it is attached to the sides of the boat with pins, just like the standard middle seat. It is compatible with Saiman rowing boats starting from model year 2008 onwards.

Fastening bed (plywood) for bow engine

Plywood plate to provide rigid support for the trolling motor

Fastening bed for battery under front

Battery mounting kit in aluminium for the use of trolling motor in the bow. To be mounted under the front seat. The mounting plate allows the battery to be securely mounted under the front seat. Cable runs must be made through the front seat, sealing the sealing ring.

Fastening bed for bow engine (plywood) 400

The mounting bed allows installation of a bow engine on Terhi 400 models for fishing. The mounting plate is made of plywood.

Fishing arch aluminum with 6 rod holders

Aluminium targa arch with six rod holders. The package includes brackets.

Fishing arch, grey

Grey targa-arch, to be mounted on the bow rail. For models 475 BR/480, additional mounting kit 700615-TER is required. Acid-proof steel. Color code RAL7031.

Fishing arch, polished

Polished targa-arch for mounting on the bow rail pair. For models 475 BR/480, a mounting kit 700615-TER is also required. Acid-proof steel.

Flag pole

Flagpole to the stern of the boat. Requires a flagpole holder 7410372-TER for installation .

Flag pole holder (submersible)

Flagpole holder for flag pole 7410371-TER. Submersible mounting on the stern of a boat.

Flag pole holder, black (surface mounting)

Flagpole holder for flag pole. Aluminium, black-painted. Surface mounting.

Fore bulkhead under rear seat

With the fore bulkhead of rear seat, you can modify the lower part of the rear seat into a lockable storage area. The dark color of the bulkhead also provides a bit visibility protection.

Harbor cover

Harbor cover protects the boat from dirt and rain while the boat is in port. The cover is not suitable for storing the boat outdoors in the winter. The cover should be stored in a warm, dry place when the boat season has ended.

Harbor cover

Harbor cover protects the boat from dirt and rain while the boat is in port. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The cover arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Harbor cover

Harbor cover protects the boat from dirt and rain while the boat is in port. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The cover arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Harbor cover

Harbor cover protects the boat from dirt and rain while the boat is in port. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The cover arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Harbor cover

Harbor cover protects the boat from dirt and rain while the boat is in port. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended.

Harbor cover

Harbor cover protects the boat from dirt and rain while the boat is in port. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The cover arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Harbor cover

Harbor cover protects the boat from dirt and rain while the boat is in port. The cover is not suitable for storing the boat outdoors in the winter. The cover should be stored in a warm, dry place when the boat season has ended.

Harbor cover

Harbor cover protects the boat from dirt and rain while the boat is in port. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The cover arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Harbor cover 400/400 C/400 CC

Harbor cover protects the boat from dirt and rain while the boat is in port. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The cover arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Harbor cover, low

Harbor cover protects the boat from dirt and rain while the boat is in port. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The cover arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Harbor- & driving canopy

Harbor and driving canopy protects from wind, rain and sun in port and offshore. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The canopy arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Interior light

LED interior light with 20 daylight-white LED light sources. IP65 waterproof. Ø 106,6 mm. 12 V. With rocker switch. 3,6 W.

Keel list cut to shape

Ideal for protecting the keel line of boat. Protects the whole keel as well as partly the bow. NOTE! One package of Terhi Fix 600g (72107-TER) is needed for the mounting of keel list.

Keel list cut to shape

Ideal for protecting the keel line of boat. Protects the whole keel as well as partly the bow. NOTE! One package of Terhi Fix 600g (72107-TER) is needed for the mounting of keel list.

Keel list 3m / 45mm

Ideal for protecting the keel line of boat. Protects the whole keel as well as partly the bow. NOTE! One package of Terhi Fix 600g (72107-TER) is needed for the mounting of keel list.

Keel list 5 m / 32 mm

Ideal for protecting the keel line of boat. Protects the whole keel as well as partly the bow. NOTE! One package of Terhi Fix 600g (72107-TER) is needed for the mounting of keel list.

Keel list cut to shape

Ideal for protecting the keel line of boat. Protects the whole keel as well as partly the bow. NOTE! One package of Terhi Fix 600g (72107-TER) is needed for the mounting of keel list.

Keel list, cut to form (2 parts)

Ideal for protecting the keel line of boat. Protects the whole keel as well as partly the bow. NOTE! One package of Terhi Fix 600g (72107-TER) is needed for the mounting of keel list.

Keellist 5m / 25mm

Ideal for protecting the keel line of boat. Protects the whole keel as well as partly the bow. NOTE! One package of Terhi Fix 600g is needed for the mounting of keel list.

Laminate set

A set of 4 mm thick high pressure laminates. The laminate set brings dignity to the boat floor.

Laminate set

A set of 4 mm thick high pressure laminates. The laminate set brings dignity to the boat floor.

Laminate set

A set of 4 mm thick high pressure laminates. The laminate set brings dignity to the boat floor.

Lid for rainwater drainage

Lid for rainwater drainage prevents for example leaves to get into the draining tube when the boat is in the port or out of the water.

Lock for outboard mounting bracket

Includes three keys.

Main switch and battery box

Battery box equipped with main switch. Suits for Terhi 400, Terhi 400 C, Terhi 445 C and Terhi 450 C boats. Mounting under the rear seat.

Mid seat with storage space

A rotationally molded spacious seat/storage box, which can be placed as a middle bench instead of the standardly fitted bench out of plywood. The seat/storage box is removable, lockable and can also accommodate a standard 110 AH battery. A small storage compartment and cup holder on the surface of the seat add to the usability, as your water bottle and cell phone are well within reach at all times. There is also a drainage tube for condensation water on the front side of the seat box. Both the seat/ storage box and the standardly fitted traditional middle bench, can be attached to three different mounting points, one of which has a locking option.

Mid seat with storage space

A rotationally molded spacious seat/storage box, which can be placed as a middle bench instead of the standardly fitted bench out of plywood. The seat/storage box is removable, lockable and can also accommodate a standard 110 AH battery. A small storage compartment and cup holder on the surface of the seat add to the usability, as your water bottle and cell phone are well within reach at all times. There is also a drainage tube for condensation water on the front side of the seat box. Both the seat/ storage box and the standardly fitted traditional middle bench, can be attached to three different mounting points, one of which has a locking option.

Mounting bed for bow engine (aluminium)

Mounting bed for bow engine enables the use of an electric bow engine in Terhi 390 boat. Material aluminium.

Navigation light 360 deg.

Plastic, all-round pole light to stern of the boat. Light colour white.

Oars 8.5´ 255 undrilled (pair)

A light and balanced sea oar laminated from selected, somewhat knotty spruce timber. A positive feature of spruce is that, besides being very light, it doesn’t draw in moist very easily. Shaped handle, symmertical blade shape with a rounded tip. Finished with water-proof special varnish. Made in Finland.

Oars 9´ / 270 cm, undrilled

A light and balanced sea oar laminated from selected, somewhat knotty spruce timber. A positive feature of spruce is that, besides being very light, it doesn’t draw in moist very easily. Shaped handle, symmertical blade shape with a rounded tip. Finished with water-proof special varnish.

Padding set (thin) for the sunbed plywood boards

These thin paddings are self-adhesive and they’re easy to keep clean. This set suits for the sunbed plywood boards of Terhi 450, 450 C, 450 CC and 450 SC (as well as the previous 445 models). A padding set for the plywood seats is sold separately.

Paddle 140 cm

A paddle laminated from clean timber with a shaped grip. Suitable both for canoes and boats. Finished with a special varnish.

Plywood parts for sunbed (445/450)

With these plywood parts you can modify the front part of the boat as a sun deck. The plywood parts are made of high-quality plastic-coated birch plywood. You can even increase comfort by acquiring cushion sets on the seats and sunbed plywoos parts. Suited for the Terhi 450 and its predecessor Terhi 445.

Plywood seat, right

With this extra seat you will a U-shaped seating area in the bow. Check also the stylish cushion set 7445010-TER.

Polished rear side rail pair (450 TC / 480 CC)

Side rail pair in polished, acid-proof steel. For the Terhi 450 TC model this rail pair can be installed as aft side rails. For the Terhi 480 CC this rail pair can be installed as an aft side rail pair and/or as a mid side rail pair. Rails improve safety on board by providing a secure handhold when boarding the boat or moving around in the boat, as well as when the boat is underway. The rails also make it easy to install various accessories, such as rod holders.

Pulling handle

With the help of the pulling bar it is easier to pull the boat out of the water to the beach. Mounting in the bow. Acid-proof steel.

Pulling handle

With the help of the pulling bar it is easier to pull the boat out of the water to the beach. Mounting in the bow. Acid-proof steel.

Railing pair

Boat railings improve safety as it is easier to move in a boat by holding on to rails and passangers can hold on to rails when the boat is moving. It is also easy to attach various types of equipment, e.g. rod holders, to the rails. Ralings also change the appearance of the boat. Made of acid-proof steel, painted in grey. Diameter ø25 mm.

Railings, complete polished

Boat railings improve safety as it is easier to move in a boat by holding on to rails and passangers can hold on to rails when the boat is moving. It is also easy to attach various types of equipment, e.g. rod holders, to the rails. Ralings also change the appearance of the boat.

Railings, pair, polished

Boat railings improve safety as it is easier to move in a boat by holding on to rails and passangers can hold on to rails when the boat is moving. It is also easy to attach various types of equipment, e.g. rod holders, to the rails. Ralings also change the appearance of the boat.

Raymarine Axiom 7-RV

The Raymarine Axiom 7 chartplotter has a large 7-inch screen and has excellent features. Axiom chartplotter displays feature a built-in GPS receiver, simple touchscreen operation, and fast quad-core performance.

Raymarine Axiom 9-RV

The Raymarine Axiom 9 chartplotter has a large 9-inch screen. Axiom chartplotter displays feature a built-in GPS receiver, simple touchscreen operation, and fast quad-core performance.

Rear seat bulkhead kit

With the bulkhead set of rear seat, you can modify the lower part of the rear seat into a lockable storage area. The dark color of the bulkhead also provides a bit visibility protection.

Rod holder, grey

Adjustable, rod holder of very high quality. Made out of acid-resistant steel. Mounting on a Ø 25mm rail (i.e. requires the railings). Length of the tube 250 mm. Easy to mount and adjust. RAL7031 (grey).

Rod holder, polished -> requires a handrail

Adjustable, rod holder of very high quality. Material acid-proof steel . Mounting on Ø 25mm rail. Length of tube 250mm. Easy to mount and adjust.

Roof railing, rea

The roof rail gives you very good support when standing behind the cabin. It is easy to mount the rail to the mounting points on the roof.

Rope handle

With the help of the rope handle (pulling rope) it is easier to pull the boat out of the water onto the beach. Easily attach the rope handle in the boweye.

Rowlock (pair)

Rowlocks for the oars, manufactured in Finland. The package includes two rowlocks. The oars do not require any drilled holes, as the rowlock is fastened around the shaft of the oar.

Rowlock, open (pair)

Open rowlock pair for oars (max diameter of oar 53 mm). Fits in 17 mm base. Locks in the base of rowlock. Rowlock has a loop for attaching a safety cord of oar. Made of cast aluminium. Manufactured in Finland.

Safety/swim ladder, adjustable (400/400 CC)

A swimming/safety ladder with a foldable stepping part. Four steps of which the lowest step is telescopic for practical length adjustment. In the upraised position the step part is fastened to the frame with a plastic clip. Mounting on stern transom.

Suitable for the Terhi 390 (from FI-TRH39001B627), 400, 400 C, 400 CC sand 440 (from FI-TRH44001D627) -models.

Seat cushions (440)

Cushions for the seats. The package includes 4 cushions. After use it is recommended to stow away the cushions in a dry place, this way the cushions last for a longer time.

Note! The points for the cushion fasteners may vary depending on production batches.

Seat paddings, thin adhesive (450 models)

This set of thin seat paddings for the plywood seats is a quick and easy way to add comfort to your boat. The paddings are self-adhesive and they’re easy to dry and keep clean. The padding for the sunbed’s plywood boards is sold separately. Suited for the Terhi 450, 450 C, 450 CC and 450 SC (as well as the previous 445/445C models). Please note that the 450 TC model has its own seat padding set (69113-TER).

Seat paddings, thin adhesive (450 TC)

This set of thin seat paddings for the plywood seats is a quick and easy way to add comfort to your boat. The paddings are self-adhesive and they’re easy to keep clean. This set suits for the Terhi 450 TC model. A padding set for the sunbed plywood boards is sold separately.

Side rail pair, polished

Boat railings improve safety as it is easier to move in a boat by holding on to rails and passangers can hold on to rails when the boat is moving. It is also easy to attach various types of equipment, e.g. rod holders, to the rails. Ralings also change the appearance of the boat.

Side railing, pair, polished

Boat railings improve safety as it is easier to move in a boat by holding on to rails and passangers can hold on to rails when the boat is moving. It is also easy to attach various types of equipment, e.g. rod holders, to the rails. Ralings also change the appearance of the boat.

Side railings for the cabin roof

A pair of side rails on the roof makes it easier to dock at the pier. A person at the pier can easily reach to the roof side rails. In addition, you can easily fasten the fenders to these side rails. It is easy to mount roof rails to the mounting points on the roof.

Siderail of windscreen, pair

A pair of rails for the side windscreens makes it easier to dock at the pier. A person at the pier can easily reach to the windscreen side rails. In addition, you can easily fasten the fenders to these rails. The packages includes two polished rails and mounting parts.

Siderail of windscreen, pair

A pair of rails for the side windscreens makes it easier to dock at the pier. A person at the pier can easily reach to the windscreen side rails. In addition, you can easily fasten the fenders to these rails. The packages includes two polished rails and mounting parts.

Siderail of windscreen, pair

A pair of rails for the side windscreens makes it easier to dock at the pier. A person at the pier can easily reach to the windscreen side rails. In addition, you can easily fasten the fenders to these rails. The packages includes two polished rails and mounting parts.

Siderail of windscreen, pair 450 TC

A pair of rails for the side windscreens makes it easier to dock at the pier. A person at the pier can easily reach to the windscreen side rails. In addition, you can easily fasten the fenders to these rails. This rail pair is required for mounting a stern canopy. The packages includes two polished rails and mounting parts.

Solar kit

Includes 45W solar panel, 8A charge controller, battery box, battery box cover and cables.

Solar kit

Includes 45W solar panel, 8A charge controller, battery box, battery box cover and cables.

Steering console complete

With this conversion package you can convert your Terhi Nodic 6020 boat (starting from model year 2016) into a wheel steerable boat! The package includes components for installing a complete driving console for Terhi Nordic 6020 with its electrical equipment. The package also includes a windscreen and a polished windscreen rail.

Steering console excl.windscreen pure white

Grey steering console suited for Terhi 400. For retrofitting. The package includes the console, steering wheel, wheel drum, steering cable, screws for mounting and the front bulkhead for the rear bench. The windshield is not included, and can be bought separately.

Also available in grey color (74080-TER).

Please note that the same outboard engine model might not work for the tiller-handle version and the console version.

Steering console excl.windscreen, grey (400)

Grey steering console suited for Terhi 400. For retrofitting. The package includes the console, steering wheel, wheel drum, steering cable, screws for mounting and the front bulkhead for the rear bench. The windshield is not included, and can be bought separately.

Also available in white color (740801-TER).

Please note that the same outboard engine model might not work for the tiller-handle version and the console version.

Stern canopy

A well-designed and high quality stern canopy increases comfort and value to your boating. Our boat canopies are designed with the different uses of boats in mind, so that they would serve the boat user the best way. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The canopy arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Stern canopy

A well-designed and high quality stern canopy increases comfort and value to your boating. Our boat canopies are designed with the different uses of boats in mind, so that they would serve the boat user the best way. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The canopy arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Stern canopy

A well-designed and high quality stern canopy increases comfort and value to your boating. Our boat canopies are designed with the different uses of boats in mind, so that they would serve the boat user the best way. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The canopy arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Stern canopy

A well-designed and high quality stern canopy increases comfort and value to your boating. Our boat canopies are designed with the different uses of boats in mind, so that they would serve the boat user the best way. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The canopy arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Stern canopy

A well-designed and high quality stern canopy increases comfort and value to your boating. Our boat canopies are designed with the different uses of boats in mind, so that they would serve the boat user the best way. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The canopy arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Stern canopy (480 TC)

A properly designed, high quality stern canopy increases comfort and usability. Our boat canopies are designed keeping in mind everything the boat can be used for, so that they serve the boat’s user in the best possible way.

Note! Mounting the canopy requires that there the windshcreen side rails (748304-TER) are installed. The canopy is not suitable for winter storage outdoors. The fabric part of the canopy should be stored in a warm, dry place when the boating season has ended. The canopy arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Stern canopy (side railing pair required)

A well-designed and high quality stern canopy increases comfort and value to your boating. Our boat canopies are designed with the different uses of boats in mind, so that they would serve the boat user the best way. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The canopy arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Stern canopy 450 SC

A well-designed and high quality stern canopy increases comfort and value to your boating. Our boat canopies are designed with the different uses of boats in mind, so that they would serve the boat user the best way. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The canopy arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Stern canopy 450 TC

A well-designed and high quality stern canopy increases comfort and value to your boating. Our boat canopies are designed with the different uses of boats in mind, so that they would serve the boat user the best way. The canopy is not suitable for storing the boat outdoors in the winter. The fabric part of the canopy should be stored in a warm, dry place when the boat season has ended. The canopy arches are not designed to withstand the weight of snow. Do not use the arches to support a winter cover.

Stern rail high, polished

Boat railings improve safety as it is easier to move in a boat by holding on to rails and passangers can hold on to rails when the boat is moving. It is also easy to attach various types of equipment, e.g. rod holders, to the rails. Ralings also change the appearance of the boat.

Stern rail, polished

Boat railings improve safety as it is easier to move in a boat by holding on to rails and passangers can hold on to rails when the boat is moving. It is also easy to attach various types of equipment, e.g. rod holders, to the rails. Ralings also change the appearance of the boat.

Storage cover

For covering the boat when the boat is out of the water. The cover does not withstand the weight of snow.

Storage cover

For covering the boat when the boat is out of the water. The cover does not withstand the weight of snow.

Storage cover

For covering the boat when the boat is out of the water. The cover does not withstand the weight of snow.

Storage cover

For covering the boat when the boat is out of the water. The cover does not withstand the weight of snow.

Storage cover

For covering the boat when the boat is out of the water. The cover does not withstand the weight of snow.

Storage cover

For covering the boat when the boat is out of the water. The cover does not withstand the weight of snow.

Storage cover 450 SC

For covering the boat when the boat is out of the water. The cover does not withstand the weight of snow.

Strainer

Strainer prevents for example leaves to get into the draining tube when the boat is in the port or out of the water.

Sunbed and -cushion

This sunbed set fits on Terhi 390. The set includes sunbed plywood parts and a foldable cushion which will be mounted on top of sunbed plywood parts with snap fasteners. Plywood parts are made of plastic coated birch plywood. The use of sunbed set requires also a seat cushion set on the boat. We recommend stowing away the cushions in a dry space after use, to prolong the lifespan of the cushions. Note! The fastening points of the cushions may vary between production batches.

Sunbed and -cushions

This sunbed set fits on Terhi 450, 450 CC and 450 SC -models. Additionally it also fits on older Terhi-models 450 C, 445 and 445 C. Includes sunbed plywood parts (2 pcs) and cushions (4 pcs) which will be mounted with snap fasteners on top of sunbed plywood parts, folding seat and seat on starbord side. Plywood parts are made of plastic coated birch plywood. The use of cushions for sunbed plywood parts requires also a seat cushion set 744501-TER on the boat. We recommend stowing away the cushions in a dry space after use, to prolong the lifespan of the cushions. Note! The fastening points of the cushions may vary between production batches.

Sunbed and -cushions

This sunbed set fits on Terhi 480 BR, 480 Sport & 480 Cabin models. The set includes sunbed plywood parts (3 pcs) and cushions (3+2 pcs). Three sunbed cushions will be mounted on top of sunbed plywood parts and two backrest cushions will be fitted to the front of the 480 BR & 480 Sport consoles. On 480 Cabin we recommend to leave the backrest cushions loose. Mounting with snap fasteners. The use of sunbed set requires also a seat cushion set on the boat. We recommend stowing away the cushions in a dry space after use, to prolong the lifespan of the cushions. Note! The fastening points of the cushions may vary between production batches.

Sunbed and -cushions

This sunbed set fits on Terhi 480 TC model. The set includes sunbed plywood parts (3 pcs) and cushions (3 pcs).The sunbed cushions will be mounted on top of sunbed plywood parts with snap fasteners. Plywood parts are made of plastic coated birch plywood. The use of sunbed set requires also seat cushion set on the boat. We recommend stowing away the cushions in a dry space after use, to prolong the lifespan of the cushions. Note! The fastening points of the cushions may vary between production batches.

Sunbed cushion

A cushion on top of sunbed plywood parts. The use of a sunbed cushion require also a sunbed plywood parts and a seat cushion set on the boat. After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of cushions may vary between production batches.

Sunbed cushions

Foldable sunbed cushion for the Terhi 390 -boat model. Sunbed cushion requires also a sunbed plywood set and cushion set for seats on the boat. The cushion will be mounted on top of the sunbed plywood parts with snap fasteners. After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of the cushions may vary between production batches. The faded cushions shown in the picture are part of the boat’s cushion set.

Sunbed cushions

These sunbed cushions fit on Terhi 480 TC -model. The set includes three cushions which will be mounted on top of sunbed plywood parts. Mounting with snap fasteners. The use of sunbed cushions requires also sunbed plywood parts and a seat cushion set on the boat. After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of the cushions may vary between production batches.

Sunbed cushions

This sunbed cushion set fits on Terhi 450, 450 CC and 450 SC -models. Additionally it also fits on older Terhi-models 450 C, 445 and 445 C. The set includes four cushions which will be mounted with snap fasteners on top of sunbed plywood parts, folding seat and seat on starbord side. The use of sunbed cushions requires also a sunbed plywood parts (744509-TER) and a seat cushion set (744501-TER) on the boat. After use it is recommended to remove the cushions to a shelter from the moisture and rain. Note! The fastening points of the cushions may vary between production batches.

Sunbed cushions (480 BR/Sport/Cabin)

Sunbed cushions for the bow of Terhi 480 BR, 480 Sport & 480 Cabin. The set includes three seat cushions and two backrest cushions for the front side of the steering consoles. Concerning the 480 Cabin we recommend leaving the backrest cushions unfastened.
After use, we recommend storing the cushions in a dry space, away from rain and moist in order to prolong the cushions’ lifespan.

Note! In order for the sunbed to be raised fully in the bow, you also need the seat cushion set and the sunbed in-fill plywood boards, which are not included in this package. The fastening points of the cushions may vary between production batches.

Sunbed plywood parts (390)

With these plywood boards a sunbed can be mounted in the bow of Terhi 390. The plywood parts are made of high-quality plastic-coated birch plywood. Please note that the sunbed or seat cushions for the bow are not included, and can be bought separately to increase comfort.

Sunbed plywood parts (450 Sloep)

With these plywood parts you can modify the front part of the boat as a sun deck. The plywood parts are made of high-quality plastic-coated birch plywood. You can even increase comfort by acquiring cushion sets on the seats and sunbed plywoos parts.

Sunbed plywood parts (480 BR/Sport)

With these plywood boards a sunbed can be formed in the bow of the 480 BR and 480 Sport models. The plywood parts are made of high-quality plastic-coated birch plywood. Please note that the sunbed cushion or the bow seat cushions are not included in the package, and should be bought separately for increased comfort.

Sunbed plywood parts (480 TC)

With these plywood boards a sunbed can be mounted in the bow of Terhi 480 TC. The plywood parts are made of high-quality plastic-coated birch plywood. Please note that the sunbed or seat cushions for the bow are not included, and can be bought separately to increase comfort.

Sunbed plywood parts (Nordic)

With these plywood parts you can modify the front part of the boat as a sun deck. The plywood parts are made of high-quality plastic-coated birch plywood. You can even increase comfort by acquiring cushion sets on the seats and sunbed plywoos parts.

Sunbed thin seat padding (450 TC)

These thin seat paddings are self-adhesive and they’re easy to dry off and keep clean. The set is designed for the sunbed plywood boards of Terhi 450 TC.

Please not that this accessory does not include the seat paddings for the seats, which are sold separately (69113-TER).

Sunbed with cushion

Includes sunbed plywood parts and a cushion which will be mounted on top of sunbed plywood parts with snap fastener. Plywood parts are made of plastic coated birch plywood. The use of a cushion for sunbed plywood parts requires also seat cushion set on the boat. We recommend stowing away the cushions in a dry space after use, to prolong the lifespan of the cushions. Note! The fastening points of the cushions may vary between production batches.

Sunbed with cushions (450 TC)

Sunbed with sun cushions, suited for Terhi 450 TC. The set includes the sunbed’s plywood boards and sunbed cushions on top of the sunbed plywood boards. The cushions will be fitted on the plywood boards with snap fasteners. The use of sunbed set requires also a cushion set for the seats on the boat. The plywood parts are made of plastic coated birch plywood.

We recommend stowing away the cushions in a dry space after use, to prolong the lifespan of the cushions.

Please note! The fastening points of the cushions may vary between production batches.

Telescopic paddle

A paddle which can be also used as a boat hook. Telescopic model with stepless adjustment. Material aluminium and plastic.

Terhi mooring package incl. bag to motor boat

The Terhi equipment bag contains a comprehensive set of equipment for mooring a boat in harbour or anchoring it at sea.

The bag contains:

bag, black (Terhi-logo)
fender, black 4 pcs
fender line 8mm 4 pcs
mooring line 12mm x 10m 1 pc
mooring line 12mm x 6m 2 pcs
anchor 1 pc
anchor line 12mm x 30m 1 pc

Terhi seat cushion (44,5/45,5x42x6 cm)

Universal seat cushion without fastening buttons. Size approximately 44,5/45,5 x 42 x 6 cm. After use it is recommended to remove the cushion to a shelter from the moisture and rain.

Terhi table

White, oval table with four cup holders. The package includes also a table leg and two bases for fitting the table (submersible and surface mounting).

Terhi-storage bin

Lightweight, plastic storage box onto the rail.

Terhi-storage box with slide rails

Lightweight plastic box with aluminium sliding rails. For storing small items. Mounting under a plywood seat. Includes mounting parts.

Thin seat paddings (400 / 400 C)

A self-adhesive thin seat padding set for the plywood benches of Terhi 400 and Terhi 400 C. The foam-like material is easy to install, maintain and keep clean. It insulates from both cold and warm. Dark grey color.